All India Trade Test – 2024 Wireman – First Year – Set 1

All India Trade Test – 2024

Wireman – First Year – Set 1

Total Questions: 75

Maximum Marks: 150

Marks per Question: 2

Negative Marking: No

Part 1: Trade Theory (Questions 1–38)

Question 1. What is the colour code for warning signs?

1. White symbol on a blue background
2. White symbol on a green background
3. Black symbol on a white background with a red border and crossbar
4. Yellow background with a black border and black symbol

Question 2. Fires caused by gases and liquefied flammable gases belong to which class?

1. Class C fire
2. Class A fire
3. Class D fire
4. Class B fire

Question 3. Which factors must be present together for a fire to occur?

1. Fuel, heat and hydrogen
2. Fuel, temperature and hydrogen
3. Fuel, hydrogen and oxygen
4. Fuel, heat and oxygen

Question 4. What is the name of the PPE shown in the figure?

1. Apron
2. Leg guards
3. Face shield
4. Hand screen

Figure: See page 2 of the original PDF.

Question 5. What does safety mean?

1. Identifying occupational hazards
2. Providing a safe working environment
3. Providing first aid to a victim
4. Freedom from or protection against harm and danger

Question 6. Which personal protective equipment (PPE) is used to protect the eyes?

1. Helmet
2. Safety goggles
3. Nose mask
4. Leather apron

Question 7. Which concept of 5S represents standardization?

1. Step 1
2. Step 2
3. Step 3
4. Step 4

Question 8. What is the name of the tool shown in the figure?

1. Combination plier
2. Wire stripper
3. Crimping tool
4. Side cutter

Figure: See page 3 of the original PDF.

Question 9. What is the name of the tool shown in the figure?

1. Poker
2. Gimlet
3. Bradawl
4. Rawl plug tool

Figure: See page 3 of the original PDF.

Question 10. A virus belongs to which category of hazard?

1. Ergonomic hazard
2. Biological hazard
3. Physical hazard
4. Chemical hazard

Question 11. Which of the following is an example of a chemical hazard?

1. Fatigue
2. Bacteria
3. Corrosive substances
4. Illness

Question 12. What is the name of the hammer shown in the figure?

1. Claw hammer
2. Straight pein hammer
3. Ball pein hammer
4. Cross pein hammer

Figure: See page 4 of the original PDF.

Question 13. On what basis is a file specified?

1. Length
2. Thickness
3. Width
4. Total length including the handle

Question 14. What is a cross-cut chisel used for?

1. Cutting keyways
2. Cutting curved grooves
3. Squaring material at corners
4. Removing metal after chain drilling

Question 15. What is a rough file used for?

1. High-quality finishing
2. Good finishing
3. Achieving a good finish while removing little metal
4. Removing a large amount of metal quickly

Question 16. What is the name of the drilling machine shown in the figure?

1. Pillar drilling machine
2. Radial drilling machine
3. Electric hand drilling machine
4. Sensitive bench drilling machine

Figure: See page 5 of the original PDF.

Question 17. What is the name of the tool shown in the figure?

1. Bent snip
2. Straight snip
3. Side-cutting plier
4. Diagonal-cutting plier

Figure: See page 6 of the original PDF.

Question 18. Which type of safety sign indicates that naked flames are prohibited?

1. Warning sign
2. Mandatory sign
3. Information sign
4. Prohibition sign

Question 19. What type of waste is used as fuel in a biogas power plant?

1. Chemical waste
2. Agricultural waste
3. Waste generated from water sources
4. Waste generated by humans and animals

Question 20. On what basis is a hacksaw blade specified?

1. Number of teeth per 10 mm
2. Number of teeth per 15 mm
3. Number of teeth per 20 mm
4. Number of teeth per 25 mm

Question 21. What is the use of the carpenter's tool shown in the figure?

1. Drawing lines parallel to a surface
2. Marking the positions of holes on wood
3. Checking the thickness of wood
4. Checking the squareness of wood

Figure: See page 7 of the original PDF.

Question 22. What is the name of the safety sign shown in the figure?

1. Information sign
2. Warning sign
3. Prohibition sign
4. Mandatory sign

Figure: See page 7 of the original PDF.

Question 23. What is the name of the safety sign shown in the figure?

1. Warning sign
2. Information sign
3. Prohibition sign
4. Mandatory sign

Figure: See page 8 of the original PDF.

Question 24. What is the shape of prohibition signs?

1. Triangular
2. Square
3. Circular
4. Hexagonal

Question 25. What is the name of the safety sign shown in the figure?

1. Prohibition sign
2. Information sign
3. Warning sign
4. Mandatory sign

Figure: See page 8 of the original PDF.

Question 26. Which waste-disposal method saves a significant amount of energy?

1. Incineration
2. Landfill
3. Composting
4. Recycling

Question 27. Which type of fire extinguisher is used to extinguish fires involving electrical equipment?

1. Foam extinguisher
2. Water-filled extinguisher
3. Stored-pressure-type extinguisher
4. Halon extinguisher

Question 28. As personal protective equipment, what does a leather apron protect?

1. Ears
2. Eyes
3. Body
4. Face

Question 29. What is cleaning?

1. Preventing excess material
2. Removing unwanted substances from the environment
3. Arranging items in an orderly sequence
4. Keeping the workplace in a safe condition

Question 30. Which screwdriver is used to tighten or loosen screws with a star-shaped head?

1. Connector screwdriver
2. Phillips screwdriver
3. Heavy-duty screwdriver
4. Insulated screwdriver

Question 31. What is the main objective of occupational health and safety?

1. Maintaining discipline
2. Cooperating with colleagues
3. Providing a safe working environment
4. Keeping the workplace clean and tidy

Question 32. What is a stock and die set used for?

1. Cutting internal threads in a cylindrical workpiece
2. Cutting external threads in a cylindrical workpiece
3. Cutting internal threads in a square workpiece
4. Cutting external threads in a square workpiece

Question 33. Which colour is used for information signs?

1. White symbol on a blue background
2. Yellow background with a black border
3. White symbol on a green background
4. Black symbol on a white background

Question 34. Which colour is used for mandatory signs?

1. Yellow background with a black border
2. White symbol on a blue background
3. White symbol on a green background
4. Black symbol on a white background

Question 35. Which background colour is used for warning signs?

1. Blue
2. White
3. Green
4. Yellow

Question 36. Which tool is used for driving and straightening nails?

1. File
2. Gimlet
3. Side-cutting plier
4. Ball pein hammer

Question 37. Which tool is used to tighten or loosen screws?

1. Combination plier
2. Electrician's knife
3. Screwdriver
4. Long-nose plier

Question 38. Which tool is used to grip small objects in places that fingers cannot reach?

1. Neon tester
2. Long-nose plier
3. Screwdriver
4. Combination plier

Part 2: Workshop Calculation and Science (Questions 39–44)

Question 39. What are the two classifications of systems of units?

1. British and metric
2. Gravitational and non-gravitational
3. Fundamental and derived
4. Metric and international

Question 40. Which of the following are fundamental units?

1. Length, mass and volume
2. Length, mass and time
3. Length, mass and area
4. Length, pressure and volume

Question 41. What does the letter 'M' represent in the MKS system?

1. Mile
2. Metre
3. Millimetre
4. Micron

Question 42. How many millimetres are there in 1 inch?

1. 2.54 mm
2. 25.4 mm
3. 24.5 mm
4. 2.45 mm

Question 43. What is the square of 0.01?

1. 0.001
2. 0.0001
3. 0.00001
4. 0.000001

Question 44. Convert the decimal fraction 0.456 into a percentage.

1. 45.6%
2. 4.56%
3. 0.456%
4. 0.0456%

Part 3: Engineering Drawing (Questions 45–50)

Question 45. Identify the conventional symbol for the material shown in the figure.

1. Water
2. Concrete
3. Asbestos
4. Glass

Figure: See page 13 of the original PDF.

Question 46. Identify the conventional symbol for the material shown in the figure.

1. Lead
2. Glass
3. Wood
4. Paper

Figure: See page 14 of the original PDF.

Question 47. Identify the tool shown in the figure.

1. Set square
2. Protractor
3. French curve
4. T-square

Figure: See page 14 of the original PDF.

Question 48. Identify the set square shown in the figure.

1. 15° set square
2. 60° set square
3. 30° set square
4. 45° set square

Figure: See page 15 of the original PDF.

Question 49. Which shape is drawn using a compass?

1. Rectangle
2. Square
3. Circle
4. Triangle

Question 50. According to standard practice, which title-block position is correct?

1. Figure A
2. Figure B
3. Figure C
4. Figure D

Refer to all four figures on pages 15–16 of the original PDF.

Part 4: Employability Skills (Questions 51–75)

Question 51. What is being in a job or at work called?

1. Employ
2. Skill
3. Knowledge
4. Aptitude

Question 52. Which section of a resume contains information such as date of birth and permanent address?

1. Career objective
2. Personal details
3. Achievements
4. Qualifications

Question 53. A person with a growth mindset is always ready to do what?

1. Rest
2. Grow, change and learn
3. Remain silent
4. Become rich

Question 54. Which job has become obsolete in the last five years?

1. STD booth
2. Ola
3. Uber
4. Swiggy

Question 55. What does ethics mean?

1. Deciding what is right and wrong in human behaviour
2. The name of a city
3. Employability skills
4. A subject unrelated to society

Question 56. What are values?

1. Not being punctual
2. Principles that guide our attitudes and actions
3. Very expensive things
4. Things that have the same value for everyone

Question 57. What is a brief statement of the objectives and principles of the Constitution called?

1. Syllabus
2. Module
3. The Preamble
4. Unit

Question 58. Identify the inappropriate term from the following.

1. Green pollution
2. Water pollution
3. Air pollution
4. Noise pollution

Question 59. What is the full form of NAPS?

1. National Apprenticeship Promotion Scheme
2. National Appointment Promoting Scheme
3. Non-Apprenticeship Promotion Scheme
4. National Advertising Promotion Scheme

Question 60. What is a major change in the manufacturing sector called?

1. Green Revolution
2. Industrial Revolution
3. Water Revolution
4. Food Revolution

Question 61. In which century did the First Industrial Revolution begin?

1. 18th century
2. 19th century
3. 20th century
4. 21st century

Question 62. Which of the following is an example of a hard skill?

1. Ability to learn quickly
2. Time management
3. Typing speed of 60 WPM
4. Spoken English

Question 63. What should you do to develop yourself?

1. Know your office
2. Know yourself
3. Know your institution
4. Know your country

Question 64. What does time management mean?

1. Completing your work on time
2. Managing time
3. A hard skill
4. Problem-solving

Question 65. What should a resume be like?

1. Short and precise
2. Attractive and colourful
3. Long and detailed
4. Full of short names and abbreviations

Question 66. What is the written description of the duties and responsibilities of a job called?

1. CV
2. Job description
3. Resume
4. Job application

Question 67. What is the next step after receiving a call for an interview?

1. Send the application form
2. Prepare a resume
3. Attend the interview
4. Send the resume

Question 68. Choose the correct WH-word to complete the sentence: “______ animal do you like?”

1. Which
2. Why
3. Where
4. When

Question 69. Which punctuation mark should be placed after 'Rohan' in the sentence “Rohan David and Ram are playing hide and seek”?

1. Comma (,)
2. Full stop (.)
3. Slash (/)
4. Hyphen (-)

Question 70. Choose the correct response to the question “How have you been?”

1. Very well, and you?
2. Thank you, and you?
3. Same to you.
4. On vacation, and you?

Question 71. Choose the correct answer to the question “When did the accident happen?”

1. At the hotel
2. During the journey
3. At 10:30 p.m. last night
4. On the table

Question 72. Choose the correct verb tense to complete the sentence: “I ______ music when I was a child.”

1. Learn
2. Am learning
3. Will learn
4. Had learnt

Question 73. What is another name for a Curriculum Vitae (CV)?

1. Circular
2. Resume
3. Job application form
4. Leave application

Question 74. Fill in the blank with the correct comparative adjective: “Your pencil is ______ than mine.”

1. Sharp
2. Sharper
3. Blunt
4. Thick

Question 75. Fill in the blank with the correct future-tense verb: “We ______ to the zoo after breakfast.”

1. Went
2. Are going
3. Had gone
4. Will go

Answer Key

Source: The answer key is provided on page 23 of the original PDF.

Note: For image-based questions, refer to the corresponding pages of the original Wireman – First Year – Set 1 question paper. The answer key above reproduces the original key; figure-dependent answers should be checked against the original illustrations.

```