1 Three phase Induction motor
Free hand sketching of Slip-ring and Squirrel cage Induction motor.
Typical wiring diagram for drum controller operation of A.C. wound rotor motor.
Drawing the schematic diagram of Autotransformer starter, DOL starter and Star Delta
Starter.
Drawing the schematic diagram of A.C. motor speed control by SCR /AC Drive.

2 Alternator
Tracing of panel wiring diagram of an alternator.
Drawing the schematic diagram of automatic voltage regulators of A.C. generators.

1 Sign & Symbol Trade related
Alternating Current
Drawing of simple electrical circuit using electrical symbols.
Drawing of sine square & triangular waves.
Diagram of battery charging circuit.
Practice in reading typical example of circuit containing R, L & C.
Reading of electrical drawing.

1. Engineering Drawing: Introduction and its importance
Relationship to other technical drawing types
Conventions
Viewing of engineering drawing sheets.
Method of Folding of printed Drawing Sheet as per BIS SP:46-2003

2 Drawing Instruments : their Standard and uses
Drawing board, T-Square, Drafter (Drafting M/c), Set Squares, Protractor.
Drawing Instrument Box (Compass, Dividers, Scale, Diagonal Scales etc).
Pencils of different Grades, Drawing pins / Clips.

1 Construction of Scales and diagonal scale

2 Practice of Lettering and Title Block

3 Dimensioning practice:
Position of dimensioning (unidirectional, aligned, oblique as per BIS SP:46-2003)
Symbols preceding the value of dimension and dimensional tolerance.
Text of dimension of repeated features, equidistance elements, circumferential
objects.

Workshop Calculation

Unit: Systems of unit- FPS, CGS, MKS/SI unit, unit of length, Mass and time, Conversion of units

Fractions : Fractions, Decimal fraction, L.C.M., H.C.F., Multiplication and Division of Fractions and Decimals, conversion of Fraction to Decimal and vice versa. Simple problems using Scientific Calculator.

Square Root : Square and Square Root, method of finding out square roots, Simple problem using calculator.

Core skills enhance knowledge, Analytical ability, problem solving ability, understanding or comprehending drawings & designs and also enriches on scientific principles. At the same time it creates the base for achieving Hard skills. To carry out any skill related task the know how about basic science & related calculation is essential as it helps in scientific way of executing the task.

1. ट्रांसफॉर्मर लैमिनेशन्स .......... के द्वारा एक-दूसरे से विद्युत-रोधी होते हैं।

अबरक पट्टी 
वार्निश के पतले आवरण
पेपर
इनमें से कोई
वार्निश के पतले आवरण

 2. एक BCD अंक को स्टोर करने के लिए इस्तेमाल बिटों की संख्या है?

8
4
1
2
4

 3. आमतौर पर पॉवर ट्रांसफॉर्मर का .......... के चारों ओर अधिकतम दक्षता रखने के लिए डिजाइन किया जाता है?

'नो-लोड'
'हाफ-लोड'
लगभग फुल लोड
10 प्रतिशत ओवरलोड
लगभग फुल लोड

 4. निम्नलिखित में से कौन-सा मीटर एक रैखिक पैमाना है?

1. एक वाइंडिंग में अनेक स्लॉट होते हैं, ध्रुवों की संख्या से अधिक होते हैं तब यह वाइंडिंग कहलाती है?

केन्द्रित (concentrated) वाइंडिंग
वितरित (distributed) वाइंडिंग
पूर्ण पिच (full pitch) वाइंडिंग 
इंटिग्रेटेड स्लॉट वाइंडिंग
वितरित (distributed) वाइंडिंग

2. 250 rpm पर रोटेट कर रहे तथा 8 ध्रुवों वाले एक अल्टरनेटर द्वारा उत्पन्न वोल्टेज की आवृति होगी?

60 Hz
50 Hz 
25 Hz
16 2/3 Hz
16 2/3 Hz

3. एक सिन्क्रोनस मोटर के स्टेटर में बैक emf सेट अप ......... पर निर्भर होगा।

Trade Theory Semester 2 JULY 2018
1. Pimary winding of a tranaformer will be short circuited if-

a) IC supply is applied

b) AC aupply is applied

c) Input impedance is increased

d) All of these

2. The name given to the transformer whose induced secondary voltage is same as the applied primary voltage is________________

a) Auto Transformer

b) Current Transformer

c) Constant Voltage Transformmer

d) Isolation Transformer

3. A transformer is rated in-

a) KW

b) KVAr

c) KVA

d) KV

Choose the correct answer:
1. The forbidden energy gap for germanium is -
a) 0.3 eV
b) 3.5 e
c) 0.72 eV
d) 1.1 eV
2. The bandgap of silicon at room temperature is -
a)1.3 eV
b) 0.7 eV

c)1.1 eV
d) 1.4 eV
3. The earth wirs are made of -
a) Copper
b) Aluminium
c)  Iron
d) Galvanized stranded stee

4. The rating of fuse is always expressed in -
a) Volts
b) Amperes
c) Ampere-volts
d) Ampere hours